The MachinistPost Blog

Drill reconditioning, machining technique, shop management — by machinists, for machinists.

All Posts Technique Business Equipment Materials Troubleshooting
89 posts · TECHNIQUE  ·  Page 3 of 4
TECHNIQUE
How To Read A Drill Point
What to look for when inspecting a drill point and how to interpret what you see.
March 21, 2028
Read Article →
TECHNIQUE
How Many Times Can You Resharpen An HSS Drill
The factors that determine how many resharpening cycles an HSS drill can deliver before retirement.
February 28, 2028
Read Article →
TECHNIQUE
How Long Should A Drill Bit Last
Expected drill bit life by material, application, and condition, and what shortens it most.
February 14, 2028
Read Article →
TECHNIQUE
Hole Saw vs Drill Bit For Large Holes
When to use a hole saw versus a large-diameter drill bit and what each approach demands from your setup.
January 31, 2028
Read Article →
TECHNIQUE
Grooving vs Drilling: Process Selection
How to decide between grooving and drilling operations when both could produce the required feature.
December 27, 2027
Read Article →
TECHNIQUE
Flood vs MQL Drilling Coolant
Comparing flood coolant and minimum quantity lubrication for drilling and which is right for your shop.
December 20, 2027
Read Article →
TECHNIQUE
Fixture Drilling vs Freehand Jig
When a dedicated fixture beats a drill jig and when the jig is the faster, cheaper solution.
December 13, 2027
Read Article →
TECHNIQUE
Extend Drill Life With Coolant Concentration
How optimizing your coolant concentration is one of the cheapest ways to extend drill bit life.
December 6, 2027
Read Article →
TECHNIQUE
Drilling Thin Sheet Metal Without Deformation
How to drill thin sheet metal cleanly without burrs, deformation, or the workpiece spinning on you.
November 22, 2027
Read Article →
TECHNIQUE
Drilling In The Field: Portable Drill Tips
How to get accurate, clean holes with a portable drill when precision equipment is not available.
September 27, 2027
Read Article →
TECHNIQUE
Drilling Best Practices Checklist
A 25-point checklist covering setup, speeds, feeds, and inspection for consistently good drilling results.
July 19, 2027
Read Article →
TECHNIQUE
Drilling Accurate Hole Patterns
How to lay out and drill accurate hole patterns without expensive fixtures or CNC equipment.
July 5, 2027
Read Article →
TECHNIQUE
Drilling A Straight Hole Without A Drill Press
Techniques for drilling straight, accurately located holes when a drill press is not available.
June 7, 2027
Read Article →
TECHNIQUE
Drill Speeds And Feeds Reference Guide
A comprehensive speeds and feeds reference for HSS drilling across the most common workpiece materials.
May 24, 2027
Read Article →
TECHNIQUE
Drill Point Thinning Explained
What web thinning does to drill point geometry, why it matters, and how it affects cutting action.
March 8, 2027
Read Article →
TECHNIQUE
Drill Point Symmetry: How To Check
Simple methods for verifying drill point symmetry on the shop floor before running a critical hole.
March 1, 2027
Read Article →
TECHNIQUE
Drill Point Regrinding Tolerances
What tolerances matter in drill point regrinding and how tight they need to be for reliable performance.
February 22, 2027
Read Article →
TECHNIQUE
Drill Point Grinding Angles And Geometry
The key grinding angles that define a properly sharpened drill point and what each angle controls.
February 15, 2027
Read Article →
TECHNIQUE
Drill Point Geometry: Conventional, Split, Notched
Comparing conventional, split, and notched drill points to match geometry to application.
February 8, 2027
Read Article →
TECHNIQUE
Drill Nomenclature: Complete Parts Reference
Every term used to describe twist drill geometry and construction, with clear definitions and context.
January 25, 2027
Read Article →
TECHNIQUE
Drill Inspection: What To Check Before Every Job
A fast, systematic drill inspection routine that catches problems before they become scrapped parts.
January 4, 2027
Read Article →
TECHNIQUE
Drill Chart: SFM To RPM Conversion
A practical SFM-to-RPM drill chart covering common diameters and materials for quick shop-floor reference.
November 30, 2026
Read Article →
TECHNIQUE
Drill Bit Sizes: Complete Guide
Fractional, number, letter, and metric drill sizes explained with charts and practical selection guidance.
November 2, 2026
Read Article →
TECHNIQUE
Drill Bit Reconditioning vs Resharpening
The difference between basic resharpening and full reconditioning, and when each is the right choice.
October 19, 2026
Read Article →
← Prev 1234 Next →